Articles by Peter F. Meier - Motor Age - Automotive training, certification & parts info
Product and Service Knowledge for Auto Pros // Home of ABRN, Aftermarket Business and Motor Age

Survey
Contests for shops today abound, from Motor Age's annual Top Shops contest to national events from CARQUEST, NAPA and more, as well as local and regional competitions.
When your shop wins an award, do you promote it to your customers?
Yes
No
We don't enter contests
Yes
56%
No
7%
We don't enter contests
37%
View Results
Thanks for sharing your information!
Motor Age magazine site header
Articles by Peter F. Meier
Articles
The engine doctor will see you now
October 13, 2009

The miss was just barely apparent at idle. As soon as the throttle plate was opened, even slightly, the miss went away. Out on the road, the engine performed perfectly at any speed, under any load. The culprit turned out to be a burnt exhaust valve on the rear bank of this Chrysler minivan causing just a slight loss of compression, but I didn't find it until I had nearly exhausted all other possibilities.

Troubleshooting power windows
October 1, 2009

A window that won't roll back up is not the only power window complaint you may face. Other common faults are windows that only move partially through their travel before grinding to a halt, work in one direction only or no longer respond to their auto up/down feature. A few simple checks, however, can often quickly and successfully locate the cause of these common problems.

Determining the missing elements in misfires
October 1, 2009

Misfires are a common drivability issue. If the misfire rate exceeds the programmed threshold, the Engine Control Module (ECM) will record the problem and turn on the Malfunction Indicator Lamp (MIL). Misfires occur when the combustion process is not as it should be. Any factor, therefore, that affects this process is suspect when it comes to diagnosis.

Owning A DSO
August 21, 2009

During the last 10 years, I?ve worked in a variety of shops and, to date, have been the only tech that owned a DSO. When techs see it in use for the first time, they invariably ask what I?m doing and why ? and then ask if they should own a scope of their own. While most have been capable of repairing problems without one, let me share a few examples of why they could have accomplished the same thing in less time and with more assurance their repair would be the correct one.

Knowing your needs will help you find the right scan tool
August 4, 2009

One of the most common questions asked on the iATN Tools and Equipment forum is "What is the best scan tool?" Unfortunately, there is no one answer to this question. The choices seem limitless, with numerous aftermarket offerings as well as those offered by the OEMs. Choosing the one right for you is dependent on several factors. By taking the time to ask yourself a few pointed questions and doing a little homework, you?ll end up with the tooling you need to take care of your needs as well as those of your customers. Here are a few topics to consider before investing your hard earned dollars.

Automotive lighting improving safety for everyone
August 1, 2009

Not only has vehicle exterior bulb technology reached new levels, so has reflector technology. New computer designs allow smaller housings, acting more like a projection lens rather than a mirror reflector. This allows designers to precisely focus the lighting pattern for better nighttime visibility

Diagnosing and repairing NVLD systems can present unique challenges
August 1, 2009

Chrysler's NVLD, or Natural Vacuum Leak Detection, system was first introduced in 2002 as an alternative to its Leak Detection Pump (LDP) method for the onboard testing of the evaporative emissions system. In an automotive application, the fuel system is sealed when the vehicle is in a key off condition. The powertrain control module (PCM) monitors the state of a switch contained within the NVLD assembly.

Quick test of ECM grounds
July 6, 2009

You all already know how important it is for an ECM/PCM (or any other control module, for that matter) to have a good power supply and good grounds. Typically, grounds fail at their point of connection, and testing these ground connections can be made a little easier using this tip.

Taking a closer look at how Ford does EGR
July 1, 2009

The use of exhaust gas recirculation to assist in emissions control is common to most manufacturers. These systems all cool combustion chamber temperatures to reduce the emissions of oxides of nitrogen, or NOx. Their function is similar. Burned gasses exiting the combustion chamber are metered back to the intake, either through a common passage or through individual, cylinder specific, passages.

Peter F. Meier


Peter Meier is an ASE-certified Master Technician, member of iATN and full-time tech in Tampa, Fla. His experience reaches back over 30 years, and his contributions to Motor Age reflect a wide variety of experience with almost every make and model.

E-News envelope

Check the e-newsletter(s) you would like to receive.

Rollover each title for information.

Distribution - Anyone interested in auto parts distribution issues will enhance their business by subscribing to The Edge from Aftermarket Business. Published every Tuesday and Friday.
Collision Repair - ABRN's e-newsletter, E-Pillar, provides up-to-date news, innovative products, technical discussions and shop management features designed to enhance your business. Published every Tuesday and Friday.
Service Repair - Sign up today and Motor Age's The Scoop will become a handy resource for your business. Benefiting auto technicians, this e-newsletter provides the latest news and analysis, technical automotive service information and business management tips. Published every Monday and Thursday.
Certified Technician - Professional automotive technicians and parts distributors seeking aftermarket products should sign up for the Certified Technician e-newsletter. This is your source for information about the latest tools, equipment and parts that can help you better service your customers. Published every Monday and Thursday.

Click here